IPA Systems

IPALASTIC
ELASTOMERIC WALL COATING
A High Quality Waterproof Coating for Exterior Application
Product Data Sheet

Product Data Sheet (PDF Format) MSDS (PDF Format) Download Adobe Acrobat

Description:

IPALASTIC elastomeric coating is a single component acrylic base protective material that expands and contracts with the movement of the substrate to which it is applied. The cured film moves without rupturing due to its elastic properties that permit a high degree of elongation.

Uses:

IPALASTIC elastomeric coating is a reflective and protective coating for vertical and overhead substrates such as concrete, masonry, block, stucco, wood, metal and other porous and non-porous surfaces.

Advantages:

Waterproof/weatherproof protection against the elements.
Highly resistant to ultraviolet radiation.
Excellent resistance to dirt pick-up and mildew.
Contains no plasticizer (will not become brittle with age).
Superior hailstone resistance.
Easy, economical, environmentally safe application.
Solvent-free, non-flammable and gives off no offensive odors.
Stable under the influence of heat and flexible at low temperatures.
Excellent reflectivity preventing accumulation of heat.
Will adhere to moist surfaces.
Monolithic – IPALASTIC liquid elastomeric coating provides a seamless uniform wall system
Flexibility – IPALASTIC has proven effective against cracking during elongation and flexural tests under laboratory and field conditions.
Versatility – IPALASTIC can be applied over concrete, masonry, block, stucco, wood, metal or other porous or non-porous surfaces.
New or Old – IPALASTIC is designed to be an effective elastomeric membrane in new, rehabilitated or restored applications.
Lightweight Problem Solver – IPALASTIC weighs less than 25 lbs. per 100 sq. ft. – Typical 2 coat application.
Reflects UV Radiation – IPALASTIC reflects the suns damaging ultraviolet radiation and reduces its destructive effects. At the same time, it reduces the surface temperature and decreases heat build-up within the subsurface or structure.
Breathes – IPALASTIC effectively seals out the weather while allowing the substrate to breathe. Breathing prevents damage by dry rot, water pocket build-up, blistering and also inhibits moisture saturation which prevents loss of insulation efficiency.
Solvent Free – IPALASTIC is an easy to apply water-based acrylic formulation. Tools clean-up with water.

TECHNICAL DATA

Shelf Life:	One year in unopened container.
Color:	IPALASTIC is available in 15 standard colors and white. Custom blended colors are available upon request. Contact your distributor for color matching details.
Texture:	IPALASTIC is manufactured in smooth, fine and coarse textures.
Coverage:	Will vary with the applicator and porosity of the surface to be coated. One gallon of IPALASTIC (Smooth) will cover approximately 100 sq. ft. at a dry film thickness of 8 mils.
Packaging:	IPALASTIC is available in 5 gallon pails and 55 gallon drums through IPA Systems Distributors.

Physical Properties: (After 2-year exposure)

Tensile strength		218 psi (1.5 MPa)
Recovery		60%
Elongation at maximum stress		187%
Elongation at break		233%
Low temperature flexibility	0°F (-17.8°C)	Pass*
	-15°F (-26.1°C)	Pass
	-34°F (-36.7°C)	Pass
Dirt pick-up resistance		Excellent
Mildew		None
Viscosity		126 k.u.
Total solids		68.9%
Weight		12.3 lbs/gallon (1.5 kg/l)
Percentage plasticizer		None

Additional Data – Maximum 2 Week Cure
Dry peel adhesion		Excellent
Wet peel adhesion		Excellent
Tensile strength at maximum stress		169 psi (1.2 MPa)
Tensile strength at break		135 psi (0.9 MPa)
Elongation at maximum stress		80%
Elongation at break		325%
Recovery after 25% elongation		72%
Low temperature flexibility at -15°F (-26.1°C), 1 week cure		Pass
300 hour Weather-O-Meter		Pass
Acid resistance		Good
Base resistance		Good
Water Immersion and Simulated Rain Test (asphalt shingle) adhesion loss, film degradation/wash-out		None

*Note: Pass = 180 bend; adhesion, tensile strength and elongation tests were conducted using the Instron Tensile Tester.

Surface Reflectivity:

Bright Sunlight 1 year exterior exposure

	Air Temp (°F)	Asphalt Shingle	Polyurethane Foam	Wood	Steel
Coated	82°	95°	92°	88°	96°
Uncoated	82°	158°	120°	117°	155°

Surface Preparation and Application:

All surfaces to be coated must be cleaned of any film, scale, loose material, oils, grease and any other foreign material that will prohibit bond or cause staining of the IPALASTIC. Any holes or uneven cracks or joints should be repaired and leveled prior to the installation of IPALASTIC. Surface should be dry; however, IPALASTIC can be applied to a moist base. Soft wood, subject to expansion and contraction, should be primed with a quality exterior latex primer. Galvanized metal should be oxidized or treated with a wash primer.

On previously coated surfaces, prestressed concrete with extremely slick surfaces, concrete which has been finished with a carborundum stone and paste, or surfaces which have been dusting, a primer coat may be required to attain a proper bond.

Where these conditions exist a trial application area should be prepared and a test made to determine adhesion and compatibility with the existing surface. See IPALASTIC “Technical Bulletin No. 1.” If the adhesion test results are not satisfactory, additional preparation or priming is necessary.

Use IPALASTIC primer on cement based repairs and chalking surfaces.

IPALASTIC may be applied with a brush, roller or spray equipment. Always apply IPALASTIC continuously to natural breaks. When detailing hairline cracks with IPALASTIC prior to coating, feather edge material away from cracks to avoid read-through.

MIXING RATIO: Apply directly from the container after mixing. DO NOT add additional water.

DRYING TIME: Two to three hours. Second coat may be applied after 24 hours.

Limitations:

Do not install IPALASTIC unless substrate and air temperature are at least 40°F (4.4°C) and not expected to drop below 40°F (4.4°C) within 24 hours. Do not apply when the surface temperature exceeds 100°F (37.8°C). IPALASTIC will not withstand negative side water pressure or rising damp. Do not apply IPALASTIC to horizontal surfaces that pond water.

CAUTION – FOR INDUSTRIAL USE ONLY

WARRANTY

This product is warranted and guaranteed to be of good quality. Manufacturer, as its sole and exclusive liability hereunder, will replace material if proved defective. THIS WARRANTY AND GUARANTEE ARE EXPRESSLY IN LIEU OF ALL OTHERS, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND MAY NOT BE EXTENDED BY REPRESENTATIVES OR ANY PERSONS, WRITTEN SALES INFORMATION, OR DRAWINGS IN ANY MANNER WHATSOEVER.

While the manufacturer recommends uses for the product based on tests believed reliable, no warranties, express or implied, or guarantee can be given as to particular methods of use or application, nor can performance be warranted, expressly or impliedly, or guaranteed under special conditions. Distributors, salespersons or company representatives are NOT authorized to extend or vary any warranties or guarantees beyond those outlined herein nor may the manufacturer’s or seller’s limitation of liability be waived or altered in any manner whatsoever.

IPALASTIC ELASTOMERIC WALL COATING A High Quality Waterproof Coating for Exterior Application Product Data Sheet